Q: Does the straight cover fit a curved.
A: No it does not. We continue to work to find a good solution unfortunately we have not been successful finding a tooling method to produce it.
Q: How do you eliminate the glare into the cab when using a insert.
A: It is very easy to fix this if it bothers you. Tape off the face with painters tape 3/4″ before the front ribs. Then paint the rest with Satin black spray paint. You can also watch this video on Youtube. Copy this link into your browser https://youtu.be/9UdpN5mUXH8
Q: Will the light bar fly off?
A: It is not the responsibility of Aerox to maintain the attachment points of the light bar. We recommend that all light bars be fastened using bolt holes not slots. The upward force of the air can push the light bar out of its mounts when using the slotted section of some mounts. Make sure your attachment bolts are tight before installation of your new Aerolidz and maintain this regularly if you are removing and installing your Aerolidz a lot.
Q: Will the light bar over heat?
A: No the Aerolidz is open on both sides and along the entire length of the back. The heat radiates as intended while in use.
Q: Why is there two sizes listed on the listing?
A: The product can be trimmed to length by cutting it with a powered miter saw. Please see our video on youtube and our website.
Q: How do we clean the Aerolidz cover?
A: Soap and water, Plastic cleaner, Plastic polish, ceramic coating are all good sources. To clean the inside you can roll up a hand towel and slide in side. Use a broom stick to push the length of the Aerolidz.
Q: How do I clean the inserts?
A: Very gently wipe with soap and water. DO NOT USE ANY CHEMICALS
Q: Does the Aerolidz fix soft top flap?
A: In most cases it does all though it was not designed to fix that. The cheap OEM top is the worst. The Premium OEM is better. The tops from Bestop is great they have the most support. The key to fixing wind noise on a soft top is to mount the light as low as possible to get the top of the light below the roof line. This will help keep the wind from directly hitting the soft top. Our brackets are at a good position to prevent that noise.
Q: Does the curved face effect the light out put?
A: NO it does reflect some light into the cab and on the hood but not much more than without.
Q: What is the difference between single row and dual row?
A: The difference is the width of the light bar. Single rows are very slim with widths of 1.5" to 2" Dual row lights are taller measuring in at 2.8" to 3"
Q; Is it safe to take cover into carwash:
A: Yes we have tested it on our own vehicles without a problem. The cover must be securely fastened to the right size light bar shown in our how to section. If your cover moves around easily you need to secure it with a zip tie or a Velcro strap before entering. You can always ask the car wash attendant to turn off the beater bar above.
Q: How to install our light bar with a JL or aftermarket switching system?
A: Easy, remove our switch that is provided on the wiring harness. Then tie those wires together and put away. Then take red battery wire on harness to you switch. Take black battery wire to ground.
Q: What's the difference between single row and dual row?
A: Single row is between 1.5" and 2" tall. Dual row is 2.8" to 3" tall.
Q: Does a triple row LED bar fit your covers?
A: Yes they fit the Dual row covers as long as the back of them measure 3.5" front to back. The shape will be either square or a long bullet shape. SEE our installation pics for sizing.
Q: The light bar is connected to the app but no control?
A: 1st rest the controller by pulling the fuse. Then make 100% sure the white wires connecting to the light bar are making contact. If still not working contact us so we can send you a new one.
Q: Remote control is not working?
A: Check to make sure there is a battery in it. If not install a 2030 watch battery.